& Mildew Stain Remover is formulated specifically for water damage
restoration and mold remediation projects where mold, mildew and other microbial
growth have impacted building materials. Sporicidin® Mold
& Mildew Stain Remover utilizes special surfactants and 7.5% hydrogen peroxide
to aggressively remove tough biological stains from porous, semi-porous, and
non-porous materials. When applied, the proprietary formula creates
deep-cleaning foam that breaks apart contamination, lifting and flushing it from
the surface, while penetrating into the surface to oxidize and remove organic
stains. Once the cleaning and bleaching action has finished, Sporicidin® Mold
& Mildew Stain Remover decomposes into harmless water and oxygen, leaving no
chemical residues to clean up. Complies with Carolina Protocol for Mold
APPLICATION METHODS: Sporicidin® Mold
& Mildew Stain Remover can be applied using a foaming sprayer, airless sprayer,
HVLP sprayer, pressure sprayer, trigger sprayer, brush, or mop.
COVERAGE RATES: Porous materials up to 600 ft2 per
gallon. Non-porous materials up to 1200 ft2 per
gallon. Coverage rates are approximate and will vary by application method,
porosity of substrate, air flow and temperature.
APPLICATION: Make certain the application device has been properly cleaned and
rinsed free of other chemical products or contaminates prior to adding
Sporicidin® Mold &
Mildew Stain Remover.
1 - Apply Sporicidin® Mold
& Mildew Stain Remover directly to the contaminated materials in a sufficient
quantity to allow the surfaces to remain wet at least 10 minutes to allow time
to penetrate and generate steady foaming action. NOTE:
When applying to open areas exposed to the outdoor environment, it is
recommended to apply using a professional-grade foaming sprayer to insure the
proper dwell time is achieved.
2 - Areas of heavy contamination and staining may be scrubbed with a stiff
bristle brush to help speed up the cleaning action and work the product deeper
into the substrate. Once the foaming action has subsided, inspect the treated
materials to see if any areas need a second application to remove stubborn
staining. If so, repeat applications until desired results are achieved.
3 - After final application, allow the treated materials to dry completely for
24 hours, during which time the brightening effects will continue. Once dried,
the surfaces may be coated and protected with one of Sporicidin’s Mold Resistant
Coatings to encapsulate and seal any residual particulates, providing long-term
protection against moisture and surface mold growth.
4 – Clean up: Discard any unused product at the end of the application – DO NOT
RETURN IT TO THE ORIGINAL CONTAINER. Rinse application device thoroughly with
water, making sure that hose, wand, and sprayer assembly are rinsed clean
LIMITATIONS: The use of this product does not guarantee health-related or indoor
air quality issues will be eliminated or reduced. Prior to using on high
pressure plastic fire sprinkler systems it is suggested to consult with the
sprinkler system manufacturer/installer to insure material compatibility with
hydrogen peroxides and/or cationic-nonionic surfactants. Avoid applying directly
onto copper plumbing commonly found in crawlspaces of older homes. Do not apply
to unsealed marble, granite, or other decorative stone surfaces. Always perform
a color stability test on fabrics and textiles prior to application.
STORAGE & DISPOSAL: Store containers in upright position in a cool, well-vented
area, away from direct sunlight. Do not allow product to freeze or become
overheated. Empty containers as thoroughly as possible and put in trash or offer
for recycling. Small spills may be flushed to an approved sewer line with
generous amounts of water. Larger spills should be contained and removed with an
inert absorbent (e.g., vermiculite, dry sand, earth), placed in a chemical waste
container and disposed of in accordance with Federal, State, and local
regulations. Do not use combustible materials, such as saw dust.
HEALTH & SAFETY: CAUTION: KEEP OUT OF REACH OF CHILDREN. Use only with adequate
ventilation. Wear protective eyewear and chemical resistant gloves. Additional
Personal Protective Equipment (PPE) including googles, face shield, respirator,
and protective clothing may be required should be selected based on a detailed
risk assessment of the tasks to be performed. Do not dilute or mix this product
with any other chemical product. For additional precautions or information,
please read product Safety Data Sheet or visit our web site at
FIRST AID: SKIN CONTACT: Flush with water for 15-20 minutes while removing
contaminated clothing. If irritation develops, seek medical attention. EYE
CONTACT: Flush with water for 15-20 minutes. Remove contact lenses, if present,
after the first 5 minutes, then continue rinsing. If irritation persists, seek
medical attention. INHALATION: Remove to fresh air and monitor. If not breathing
or if breathing is irregular, provide artificial respiration or oxygen. If
breathing difficulty continues, seek medical attention. INGESTION: Seek
medical attention. Have person sip a glass of water if able to do so. Do not
induce vomiting unless directed to do so by medical professional.